Baumatic BTC675SS Manuale Utente

my BTC675SS/BTC975SS Cooker Hood

* If you are using the appliance in recirculation mode, then PLEASE NOTE that some of the vent in the upper chimney section must be exposed. You will

Cleaning your Baumatic cooker hood IMPORTANT: BEFORE CLEANING, ALWAYS ENSURE THAT YOU HAVE SWITCHED YOUR COOKER HOOD OFF AT THE OMNI-POLAR SWITCH, S

o DO NOT WASH THE GREASE FILTER(S) IN A DISHWASHER. Maintenance Removing and cleaning the grease filter(s) o First remove the grease filter(s)

o Soak the grease filter(s) in hot water and washing up liquid for at least 3 minutes. Then use a soft brush to loosen any grease deposits that have

o Find the bulb that requires replacement, you will find it located in the light fixture which is inside the exposed section of the canopy.

3) Turn the carbon filter anticlockwise, until you feel it click into place. o Repeat this process for the second carbon filter. You need to

Electrical connection YOUR COOKER HOOD IS INTENDED FOR FITTED AND PERMANENT INSTALLATION. o The cooker hood’s power cable must be fitted upstream

17Before beginning installation o Check that the product purchased is of a suitable size for the chosen installation area. In addition check whethe

Extraction mode or recirculation mode? IMPORTANT: YOU WILL HAVE TO DECIDE BEFORE INSTALLING YOUR COOKER HOOD WHETHER TO USE IT IN EXTRACTION MODE OR

IMPORTANT: YOUR COOKER HOOD SHOULD BE CONNECTED TO YOUR MAINS SUPPLY AFTER THE REST OF THE INSTALLATION PROCESS HAS BEEN COMPLETED. 1) Remove the gr

User Manual for your Baumatic BTC675SS 60cm Cooker hood BTC975SS 90 cm Cooker hood NOTE: This User Instruction Manual contains im

2a) The support screw holes are indicated by figure A in this drawing and the anchoring screw holes are indicated by figure B. 3) Using a drill bit

6) Hang the hood onto the support screws. 7) Fully tighten the support screws (A) and then screw the anchoring screws (B) through

Connecting to external ducting 8) Connect the coupling to the top of the cooker hood, and then connect a 125 mm ducting hose to the coupling (please

10) Lift chimney section (D) upwards until it reaches the ceiling. You must ensure that it is perpendicular to the hood. o Mark the

12) Using an 8 mm drill bit, drill out two holes on the pencil markings that you made in step 11. Insert rawl plugs into the holes and

Completing the installation o If you are setting the appliance to recirculation mode, then you should now fit the two carbon filters. See the “Fitti

o If the hood is set up for extraction mode, check that the ducting hose and discharge outlet are not blocked. My cooker hood has switched off duri

United Kingdom Czech Republic Baumatic Ltd., Baumatic CR spol s.r.o. Baumatic Buildings, Průmyslová zóna Sever 696 6 Bennet Road, 460 11 Libere

3Contents Page Environmental note 4 IMPORTANT SAFETY INFORMATION 5 – 7 Specifications of your cooker hood 8 – 10 BTC675SS

ENVIRONMENTAL NOTE Note: Before discarding an old appliance, switch off and disconnect it from the power supply. Cut off and render any plug useles

IMPORTANT SAFETY INFORMATION Your safety is of the utmost importance to Baumatic. Please make sure that you read this instruction booklet before att

o The edges of the cooker hood are sharp – be mindful of this as you handle your appliance, especially during installation and cleaning. DO NOT CLEAN

o Remember that when in extraction mode, your cooker hood is removing air from your room. Ensure that proper ventilation measures are being observed

Specifications of your cooker hood BTC675SS PRODUCT DIMENSIONS Height: 540 - 920 mm Width: 600 mm Depth: 490 mm DIMENSIONS OF CHIMN

BTC975SS PRODUCT DIMENSIONS Height: 540 - 920 mm Width: 900 mm Depth: 490 mm DIMENSIONS OF CHIMNEY SECTION: Width: 303 mm Depth: 27